Rebel's Run Ranch

Add wheels and hitch to your Loading Chute so you can make it quick and easy to move, and you can pull it behind your three wheeler or other small motorized vehicle. With wheels added, you will not have to break it down for moving if you are using it on several locations around your farm.

This Loading Chute is like the chute pictured here, but is adjustable in height and unlike the pictured loading chute, the support bar at 30'' is removable and the ramp can be dropped down to a 12" height so the ramp can also be used for loading animals into a stock trailer. This makes the Loading Chute adjustable for a 30" height, or a 12" height depending on where you are loading animals. Material used to make the Loading Chute: 16 gauge pipe ends and 18 gauge pipe sides. Wire mesh is 6 gauge. Measurements: Ramp is 5’ long x 17” wide (20 lbs.). Side panels are 5’ long x 5’ high at the tallest point (26 lbs. each), 4ft at the lower point. Bows are 21” outside width, 18” inside width. (tall bow 16lbs.- short bow 14lbs) . The front bow is 6’-6” tall, the back bow is 5’ tall. Total weight of the Loading Chute is 102 lbs. Maximum animal weight: approx. 400 lbs. The Loading Chute breaks down into 5 pieces: 2 side panels (26 lbs. each), 1 front bow (16lbs.), 1 rear bow (14 lbs.), and 1 ramp (20 lbs.). @ 102lbs total. It can quickly and easily be disassembled for moving, hauling, or storage. The drop pins used to assemble your chute are permanently attached to the chute so they can not be lost in transit, and easily slide up and down for quick assembly. Add wheels and hitch to your LOADING CHUTE so you can make it quick and easy to move, and you can pull it behind your three wheeler or other small motorized vehicles. With wheels added, you will not have to break it down for moving if you are using it on several locations of your farm. Weight of the Loading Chute with the added wheels and hitch is 143 lbs. The maximum load weight is approximately 400 lbs. *The wheels are removable.

Northeast Gate Company can build a Custom-Sized Tote to fit any of your hauling needs. They can manufacture totes for the back of a truck, trailer, or even golf carts!

Dividers can be added to your Goat Tote from side to side or front to back. With the side to side divider, you will be able to load your animal into the back of the tote, then latch the divider, and load your other animal into the front. With a front to back divider, animals can be loaded into the right side, latch the divider, then load into the left side.

The Pig Totes are built the same as the Goat Tote, but with 4 divided sections and 2 front doors. There are 4 compartments withing the Pig Totes, however, the middle gates can be left open to haul 2 pigs. All Pig Totes are 47" wide and made with 18 gauge galvanized pipe and 6 gauge galvanized wire mesh sides. *5' Pig Tote has 4 compartments with each approximately 24" x 30", but with the middle gates open the 2 compartments will be 24" x 60". *6' Pig Tote has 4 compartments with each approximately 24" x 36", but with the middle gates open the 2 compartments will be 24" x 72". *8' Pig Tote has 4 compartments with each approximately 24" x 48", but with the middle gates open the 2 compartments will be 24" x 96".

Just like the Goat Tote, but with a metal top. This top helps to keep your animals protected from the elements. A nice option for long transports or transports in inclement weather.

The Goat/Pig Tote Cover is made of a heavy duty vinyl/nylon. Now, all covers feature a clear vinyl window at the rear of the tote so your animals can bee seen from your rear truck window. The sides can be rolled up or down depending on the weather. The cover can be attached to the tote using regular cable ties. *Goat/Pig Tote Covers can be manufactured in other colors beside white. The charge for a color other than white is $35.00. We DO NOT provide personalization.

Designed to fit trucks with long beds, this 8' Goat Tote is ideal for hauling any kind of small animal. To load your animals, you can slide part of the front gate or you can open the entire door. To make loading easier, please check out our Loading Chute. You can add-on a Goat Tote Cover or equip your Goat Tote with Dividers.

The easiest way to haul any small animal! Goats, sheep, dogs, pigs, even miniature horses can fit in this handy piece of equipment! Available in three different lenghts: 5', 6', and 8' OR it can be customized to fit whatever you need! Just slide it into your truck, strap it secure and load your animals. To help with loading, check out our Loading Chute. Many add-on's are available too! The Goat Tote Cover helps keep animals out of the rain, wind, snow, and sun. There are also Goat Tote Dividers that will enable you to keep animals separated.

The Original Goat Tote! If you have a goat, sheep, dog, pig, chicken, dog, small sized miniature horse or donkey, or any kind of small animal, this is the handiest piece of equipment you can own. The regular size 5ft Goat Tote with cover weighs only about 80 pounds and can be loaded easily, just slide it into your pickup. To load animals into the Goat Tote, you can slide part of the front gate or you can open the entire door. You can also purchase a Loading Chute to aid in loading animals.

This picture is of a 3 Head Piece Chariot...hopefully a 5 Head Piece Chariot picture will be coming soon! However, the Chariot is the same concept, just with 5 Head Pieces. Attach your Chariot to an ATV with the included T-shaped drop pin hitch and you are ready to get working!

If you have a lot of goats or sheep to get into shape, the 6 Head Piece Chariot is for you! This piece of equipment can save you hours of work by walking 6 goats at once instead of one at a time!

Exercising 4 of your goats or sheep gets the work done so much faster! Just attached the Chariot to your ATV with the included T-shaped drop pin hitch, secure your animals and then get to work.

This Chariot is a convenient way to exercise 3 of animals at once. A T-shaped drop pin hitch attaches the Chariot to your ATV.

These Chariots are a convenient way to exercise your goats or sheep. They can be manufactured with 2 head pieces up to 6 head pieces. Just hitch the Chariot to your ATV, secure your animal in the head piece and go. The Chariots have a T-shaped drop pin latch.

The Pack Mule is made similar to the Goat Butler, but it does not have a lift, winch cables, or brake. It does have the swivel tongue and side rails, it is also the same size as the Goat Butler. The Pack Mule’s primary function is to haul “stuff” like hay, grain, water, show supplies, etc. You can even transport an animal on the Pack Mule by simply installing the removable head piece. You can work and groom the animal if no lift is needed to do so. *300 lb. weight capacity.

The Goat Butler is a fitting stand, but with many extras! Features of the Goat Butler include:  Comes with “flat-free” 10” tires.  Has sealed ball bearing rollers and pulleys.  Includes a 800 lb. brake winch.  Raises 30” from deck (35” from ground)  Removable side panels.  400 lb. weight capacity.  Platform size is 19”x45”.

The Milking Head Piece can be added to the Fitting Stand. Just remove the regular head piece and replace it with the Milking Head Piece. It makes milking duties so much easier!

You can purchase this Wheel Kit to add to your older Fitting Stand.

All fitting stands come standard with ramp, side panels, standard head piece with plastic chain, and wheels. The floor is 23" tall. The stand folds up flat for transporting. The deck is 48" long and 19 1/2" wide. Complete your Fitting Stand by adding on the Milking Head Piece!

NEW PRODUCT! This Wall Mount Feed Pan allows you to feed your animals at the height you want. Eliminates plastic feed troughs and feed pans on the groundthat break, get knocked off or dumped over...wasting your feed. 16" front to back 48" wide 3" deep

Double Side Bulk Grain Feeder works well for ADULT Goats and Sheep. This feeder will also work for other animals approximately the same size as ADULT goats and sheep. Trough is 18” off the ground.

This feeder is for all types of goats and sheep, even animals with horns. V-shaped trough, grain area is 12 1/2 inches inside width, 6 inches deep. The feeder is on skids to make moving easier. The top bar prevents animals from standing in trough. 12 inches from the ground to top of trough, 8 inches between trough and top panel. Feeder is 8 ft long.

The Heavy Duty Hay Rack with Trough is built extra tough for small animals. It comes with the option of either bars or wire mesh (shown at left). The added trough catches your valuable hay as animals eat, thus reducing waste and saving your money. A rain canopy and frame can be added to these hay racks for further protection of your hay.

Add a frame and canopy to a Heavy Duty or Freestanding Hay Rack. This set up provides easy access for opening to fill with hay. Can open from both sides to add flakes of hay or the canopy will lift off to add an entire bale. It comes with a clamp attachment with slide in holder for the canopy top. Camopy can be attached to frame with rope or zip ties. The cover is waterproof, UV resistant, and will not crack or become brittle in cold weather. White is the standard color of the canopy, however, other colors are available for an additional $10.00.

Just drop a square bale of hay in these feeders and cut the strings. The hay rack breaks down and disassembles into 3 pieces for easy moving. This hay rack can be made with bars or wire mesh, you decide...it's the same price.

This is the new mini hay and grain feeder. It is half the width of our current Hanging Stall Feeder pictured above and works much better for miniature horses and donkeys. There is more distance between the hay and the pan so livestock with heads larger than sheep or goats can get their head in and out better to eat grain. Measurements: Overall Height - 20", Hay Manger - 12", Width - 12-1/2", Deep - 14".

This feeder is ideal to use in stalls, kidding pens, or at shows. Hooks in back for easy attachment to fence or gate. Has section for hay and grain. Made with bars or 4” x 4” wire mesh (pictured below). Ideal for all smaller sized livestock such as alpacas, llamas, goats, sheep, etc. Here at Rebel's Run Ranch, we have had three of these since 2006 and we still use them today (2016)! Feeders are made with galvanized metal and POWDER COATED "Wheel Grey" unless another color listed is requested. Note: Feeder can be mounted on the wall, or attach included hooks for hanging on board, pipe, etc

A 6' Hay Rack that can be folded flat against the wall, and latched, when hay rack is not being used. The Fold Up Wall Mount Hay Rack is 76" long x 24" tall x 22" wide top when open.

Wall Mount Hay Rack with 4"x4" wire pictured, ideal to use with goats, sheep, mini horses, alpacas, llamas, etc. The feeders are made with galvanized steel and comes with wall mount brackets. This Wall Mount Hay Rack is available in 4’ and 8’ sizes. A movable Hay Rack like the ones pictured above is available with hooks instead of wall mount brackets, to hang on a board or pipe fence (specify size of hooks needed) . 4"x 4" - 6 gauge wire mesh back will be added to the open back area, to prevent hay from falling out of the back side of the hay rack. Item # (WMHR4.HB) 4 ft. SL Wall Mount Hay Rack with fence hooks (specify size of pipe or board that the hay rack will be used on) and 4"x 4" mesh back panel added - (12" wide at top, 18" tall, 4' long) - $104.00 Item # (WMHR8.HB) 8 ft. SL Wall Mount Hay Rack with fence hooks (specify size of pipe or board that the hay rack will be used on) and 4"x 4" mesh back panel added - (24" wide at top, 18" tall, 8' long) - $175.00. If you a size other than 4' or 8', let us know. Customization is available. Just call for pricing.

Lightweight, stack-able and a perfect choice to take to shows. Measurements of Hay Basket: 19.5" wide at top 16.5" wide at bottom 10" front to back at top 2" front to back at bottom 20" tall Standard powder coated shipped Color is Powder Coated BLACK, if you prefer another basic color than black, let us know. Northeast Gate Company can customize this product to fit your space! Just let us know your dimensions and we can do our best to accommodate your needs!

These racks are ideal for feeding large bales of hay. Hay is kept off of the ground. The Hay Riser Hay Rack will fold up flat when not in use for easy storage when it’s not being used. Holds up to 1800 lb. bales, round or square. Included safety roll bars on ends prevent hay from tipping or rack folding shut when no hay is on the rack. Made of 1 3/8” x 14 gauge tubing.

Another Add-On Option for your Big Bale Round Hay Feeder is the Big Bale Trough. This trough will further help to keep your hay from getting all over the ground.

Add on a Big Bale Roof Frame to your Big Bale Round Hay Feeder to help protect your hay from the elements. Customer supplies the roofing materials which could be wood, metal or a large tarp. This Big Bale Round Hay Feeder with the roof frame will eliminate a lot of wasted hay, saving you money in the long run.

The Big Bale Round Hay Feeder is also manufactured the same way as the above feeder, but using 4” x 4” wire mesh instead of bars. This feeder is 18 pounds lighter than the Big Bale Round Hay Feeder with bars. Check out the Big Bale Roof Frame to add-on to your Big Bale Round Hay Feeder to further protect your hay from the elements. Also, you can add-on a Bale Bale Trough to catch any hay that may fall through.

The Big Bale Round Hay Feeder is a must for all goat and sheep producers! Your hay is kept off of the ground and it helps keep your animals off of your hay. This Round Bale Hay feeder is 4' tall by 6' x 6' wide. Built with galvanized steel, 1-5/8" round tube on the outer frame. 1- 3/8" round tube curved bars, and 1" round tube vertical bar ends. The spacing between the feeder bars is 6-1/2”. Feeder Bars are set on 8" centers. 15" from the ground to the hay section. Door has a spring loaded latch to prevent livestock from opening. Add-on options include the Big Bale Roof Frame and the Big Bale Trough. Also, if you have large animals, such as cows, mules, llamas, etc. this Big Bale Round Hay Feeder can be made higher. Click here to see the taller version of the Big Bale Round Hay Feeder.

*Please note that the 2" x 4" Wire Bow Gate and Panels shown have an added metal bottom.

2" x 4" Wire Panels make it more difficult for livestock to climb on or stick their head through. A good option for lambs or kids who can fit their heads through a 4" x 4" opening.

Panel Gate's are a useful addition to any fence enclosure you may have. Keeps the animals in while allowing you to enter with necessary equipment, such as tractors or mowers. *Please note that the latch is not included with this gate. Panel Gates come standard with a metal chain.

Effortlessly access your pens with these bow gates. They swing both ways and are manufactured with a spring loaded latch. These can be set up with the portables panels or can be added to existing structures. Don't forget, we can make these custom sized to fit your space!

Portable Panels made with 4" x 4" wire have been very popular for sheep and goats. You can easily hang feeders on these panels. All sizes of portable panels can be inter-changed. Each panel connects with either drop pins or rods. Pens can be made as big or small as your want them by attaching panels together. They are easy to set up, move and take down. These are a great option for kidding pens, isolation pens, stalls, expos, or petting zoos.

This set up includes the 650 lbs. Creep Feeder Box, 2 side panels, and a bow gate entrance with adjustable roller entrance for kids/lambs. The added bow gate makes entering the creep area very useful when needing to catch a kid/lamb or when the trough needs cleaned out.

Creep Feeder has an adjustable feed flow control and entrance gate that is also adjustable depending on the size of lambs and kids. Panels attach with drop pins for easy entry if needed. Feed is poured in easily from the top of the feeder on the back side. Holds 650 lbs of feed. *Includes creep feeder, 2 side panels, and front creep feeder panel with adjustable creep door.

Our Creep Feeder is available alone without Pen. Feeding area has adjustable sliding feed control panel to manage how full feeder stays. Grain area will hold 650lbs of feed. Top has a lid for easy feed filling from the back of the feeder. This creep feeder is galvanized. NEW added feature at no extra charge, these creep feeders now come with a rain visor that can be raised or lowered over the feeding area to protect the feed from the weather. Powder coated in your color choice. Creep Feeder Box is 50" wide x 36" deep. Rain visor is 9" deep x 50" wide. Feeding trough are is 5" deep x 48" wide. Trough is 4" tall. Top lip of trough is 11 1/2" off the ground.

This is a 150 lb. feed capacity creep feeder. It has a roller gate on the front that adjusts every 2" so that the openings can be made 4", 6" or 8". This creep feeder is 36" long by 24" wide and 30" tall on 4" legs and it is all galvanized, then powder coated in your color choice. Ideal for the Goat or Sheep Rancher with smaller sized herds so they can purchase a creep feeder with entrance creep area attached. This feeder weighs @ 80lbs empty.

Add this panel to your kidding pens to allow kids or lambs to enter to a protected area and prevent doe or ewe from laying on them. Also good in grafting pens when doe is not in the Grafting Panel. This panel will fit inside of our 5’x5’ Kidding Pen or any other 5’ wide stalled area.

Use for grafting kids to other does or ewes by having receiving animal's head caught and restrained so kids/lambs can be easily grafted. This panel will interchange and attach to our other portable panels to be used in pens, or can be used alone. Grafting Panel pictured as a complete pen set up but sold as an individual item.

For those ranchers that don't have that extra person around to hold lambs or kids to castrate or band, the BOY BASKET can make this job much easier. This holding basket is made with 6 gauge, 4" x 4" wire. The legs hang down between the mesh giving you safe and easy access to the job at hand.

Contact us for more information.

Easy Feeder Panels: a one of a kind item manufactured by Northeast Gate Company. Feed your goats or sheep from the outside of the pen. These panels make feeding your goats and sheep simple and easy. Door latch stays shut while filling up your feeder without having to fight pouring feed around animal’s heads while they are trying to eat. Once feeder is full, the door can be opened and animals can eat with ease. Once finished, the door can be latched shut again, keeping feeders clean by keeping animals out of feed trough when not in use. The feed trough is quick and easy to remove for cleaning if needed. These panels will also attach to our other 5ft. and 10 ft. panels or by using #PPFH-wall pockets and can be attached to an existing wall or post (see page 29). You can also order custom sized EZ Feeder Panels! The EZ Feeder products are 1 3/8" x 16 gauge frame and 1" x 16 gauge feed door and hay rack. 4"x 4" x 6 gauge welded wire mesh insert. The EZ Feeder Panel can also be used in a fence line for large herd feeding needs.

These Pasture Gates were designed with sheep and goats in mind. They are made with 4" x 4" wire, instead of bars. Small animals are unable to get out through. Pasture Gates come with a chain latch and mounting hardware (the latch in the picture was added by the owner). Pasture Gates come in several different heights of 4', 5', and 6'. These, like most of our other products, can also be customized to fit your space requirements.

This Swinging Stop Gate can be added to your GoatMaster Working Chute at the bottom of the ramp to hold an animal in the ramp area.

Working Chute includes stand and ramp. Versatility is the key to making a long days work short. This chute has the unique feature of a sorting gate built into a working chute, therefore, allowing one person the ability to hold, work, and sort animals with ease. This chute has a self-latching head gate which adjusts from 3 to 7 inches when closed, for small or large animals. Nose bar included for tattooing and ear tagging. Panels open on both sides for easy access to animals for hoof trimming, vaccinating, treating wounds, etc. The GoatMaster Working Chute also features a medicine tray on top and drench gun holders. Made from all galvanized metal, and powder coated, this chute is guaranteed to last. Portable Panels will interchange with this chute to make alleys and pens.

Working Chute designed and priced for the Sheep or Goat Rancher with smaller herds. This chute sets on the ground. The head catch is the same style as our grafting panels. Makes working goats by one person much easier. Swing gate in back to hold the goat in the chute once they enter. Once the head is caught, doors can open on either side to give shots, trim hooves, etc. With this chute being at ground level, it can also be used for grafting lamb/kids. Panels can be purchased separately and attached behind, or to the side of the chute to make alleyways, holding pens, and grafting pens, if needed.

This Digital Scale weighs animals up to 2000 lbs This heavy duty vet scale is perfect for weighing medium sized animals, such as calves. It comes with two ramps on both sides for easy weighing. The size of this unit is 50”x20”x4”. It is build using a mild steel frame, 1/5” steel deck plate with diamond cut surface, 4 alloy steel shear beam load cells, anit-slip diamond cut texture, quick indicator disconnector, Prime PS-IN101 indicator with serial output. Package configured and calibrated with 10000 divisions. This scale will fit the Northeast Gate Company Heavy Duty Scale Cage ONLY.

Use this cage with the VS1000 or the VS2000 digital scale for accurate readings when weighing larger sized animals such as calves. Scale Cage includes 2 side panels and tow door panels that pin together to make the scale cage. This cage is 4’ tall, clearance from platform to bottom of cross bar is 43 ½”. Inside dimensions: 20 ¼” x 63” long. This cage is made of all 1 3/8” x 16 gauge galvanized steel tubing and weighs 120 lbs.

Use this cage with the VS1000 scale for accurate readings when weighing animals. Ideal for goats, sheep, and other small livestock. This Scale Cage can be incorporated into our Working Systems. The Scale Cage includes 2 side panels and 2 door panels that fit together to make the Scale Cage. Northeast Gate Company can also build a Scale Cage to fit your existing scale.

The VS1000 Digital Scale is the best customer value in the industry! Perfect for weighing hogs, sheep, or goats. With a sensitivity of 0.2 lbs., ideal for farms or labs that need exact accuracy. The indicator features large easy to read digital readout in either pounds (lbs.) or kilograms (kgs.). It operates on 120v AC power and/or batteries. The exclusive lock-on feature averages the animal’s weight, thus eliminating the problem of animal movement during the weighing process. The scales are calibrate and balanced at the factory, eliminating the need for an installation technician. Install the sale, press the “Zero” button, and you are ready to weigh! This also allows you to compensate for manure, mud, or snow build-up on the scale surface. Weight indicator has keys for ON/OFF, HOLD, UNITS & TARE. Pre-calibrated and ready to use. Stainless steel cover with non-slip rubber mat. Six month warranty. INCLUDES: scale platform, digital display, rubber mat, ac adapter and wall mounting bracket.

When placed in an alley way, an animal can either go straight, or to either side.

When you place this 2 - Way Sorting Gate in an alley way, you can sort animals one way or the other.

Components: - GST402 (2' Solid Alley Panel) - GST408 (8' Solid Alley Panel) - GST406A (2 - 6' Solid Curved Tub Panels) - FSTB408 (8' Solid Tub Sweep Gate) - GSTB408 (Tub Support Bow/Ground Bar) - GG (Guillotine Gate) - STGT (Swinging Stop Gate) - GST410 (10' Solid Alley Panel) - GST410D (10' Solid Alley Panel with drop down section) - GP410 (10' Portable Panel) - GP405 (5' Portable Panel) - GP4025 (36" Walk Thru Bow Gate) - GPG405 (5' Bow Gate) - GMWCEL - GoatMaster Working Chute with Stand/Ramp

Components: - we

Components: - GST408 (8' Solid Alley Panel) - GST406A (2 - 6' Solid Curved Tub Panels) - GST402 (2' Solid Alley Panel) - GSTG408 (8' Solid Tub Sweep Gate) - GSTB408 (Tub Support Bow/Ground Bar) - GG - Guillotine Gate - STGT (Swinging Stop Gate) - GST410 (10' Solid Alley Panel with drop down section) - GP410 (10' Portable Panel) - GP405 (5' Portable Panel) - GP4025 (36" Walk Thru Bow Gate)

Components: - GST408 (8' Solid Alley Panel) -GST402 (2' Solid Alley Panel) - GST406A (2 - 6' Solid Curved Tub Panels) - GSTB408 (8' Solid Tub Sweep) - GSTB408 (Tub Support Bow/Ground Bar) - GG (Guillotine Gate) - STGT (Swinging Stop Gate) - GST410 (10' Solid Alley Panel) - GST410D (10' Solid Alley Panel with Drop down section)

Either of these gates can be added to your Working System to make your work easier. The Swinging Stop Gate can be used behind the working chute or in alleys. It attaches to the chute or portable panels.

This system is made up of the following components: - GST408 (8' Solid Alley Panel) - GST402 (2' Solid Alley Panel) - GST406A (2 - 6' Solid Alley Tub Panels) - GSTG408 (8' Solid Tub Sweep Gate) - GSTB408 (8' Tub Support Bow and Bar) - GG (Guillotine Gate)

Take the work out of handling your sheep/goats with a Northeast Gate Company Working System. Our corral systems are modular so you can design almost any style of system. In addition, numerous options can easily be added to the systems including the GoatMaster Working Chute, scales, and different styles of sort and stop gates. Please look through the different examples of Working Systems that we have featured on this site.

Northeast Gate Company’s Dog Kennels are built to last. They are manufactured with 2”x4” 6 gauge welded wire. The pen door has a spring latch. This picture features our Rhodesian Ridgeback, Dixie. When we aren’t home, she gets to stay in a Dog Kennel manufactured by Northeast Gate Company. She is a large, active dog and this pen has held up remarkably. Prior to this pen, we had a pen from a local farm store…Dixie had the latch busted off after 3 days. ITEM # Weight ITEM DESCRIPTION Price DK505 41 5’x5’ Panel $87.00 DK510 77 5’x10’ Panel $155.00 DKG505 54 5’x5’ Panel with Gate $154.00 DKG510 94 5’x10’ Panel with Gate$218.00 DK605 47 6’x5’ Panel $100.00 DK610 89 6’x10’ Panel $177.00 DKG605 63 6’x5’ Panel with Gate $172.00 DKG610 109 6’x10’ Panel with Gate$245.00